- Bộ lập trình PLC, cáp lập trình
- Màn hình HMI
- Cảm biến, phụ kiện
- Biến tần, khởi động mềm
- Máy cắt, Aptomat, khởi động từ
- Thiết bị đo lường, bảo vệ
- Thiết bị công nghiệp, tự động hóa
- Thủy lực, khí nén, van công nghiệp
- Motor, Servo motor, Servo Amplifier
- Thyristor, Module, SCR, SSR, Diode
- Phụ kiện tủ điện và vỏ tủ điện
- Cáp điện, ống bảo vệ cáp
- Thiết bị điện trung thế, truyền tải
- Thiết bị chống sét, kim thu sét
- Dụng cụ cầm tay, dụng cụ tool
- ATS, UPS, tụ bù, cuộn kháng
-
Thiết bị ngành xi măng, thép, nhiệt điện
-
Thiết bị thanh lí-hàng tháo máy
Công tắc áp suất CS-V 0.35MPa
1. The CS type and CS-IV type transmitters block the oil filter clogging alarm in the form of a switch, or cut off the control circuit related to the hydraulic system in the form of a switch, thereby protecting the safety of the system.
The connection thread of the CS-III type differential pressure transmitter is M22X1.5.
The connection size of the CM type differential pressure transmitter is the same as that of the CS-II and CS-V types, and can be used for domestic ZU type and XU type filters.
The CMS type differential pressure transmitter is similar to the CM type with visual indication, CS-V and CMS type, but no visual indication.
2, CM-I type is the visual differential pressure transmitter, the red indicator button at the upper end of the transmitter highlights the action of the transmitter and has alarmed. When cleaning or replacing the filter element, the red indicator button of the transmitter should be manually Reset, the connector thread of the transmitter is M22X1.5.
The CMS type transmitter combines the power transmission with the target transmission, enabling both power transmission and target transmission. It combines electric transmission with visual communication to enable both electric and visual alarms. When the filter element is cleaned or replaced, the red indicator button of the transmitter is automatically reset.
If the electrical signal cannot be alarmed due to a fault in the electrical component or the line, the other end can also send an alarm to accurately alarm, thus improving the reliability of the transmitter.
When the hydraulic system is working, the filter element in the oil filter is blocked by the pollutant, and the pressure of the inlet and outlet generates a pressure difference. When the pressure difference increases to the set value of the transmitter, the switch of the transmitter is turned on and the signal is alarmed. At the same time, the other end of the message shows that the red button of the transmitter pops up to indicate an alarm, indicating that the system operator should clean or replace the filter element in time to ensure the normal operation of the hydraulic system.
The basic function of the differential pressure signaling device is that during the working process of the hydraulic system, the impurity particles in the oil are blocked by the filter element in the oil filter, so that the filter element is gradually blocked, and the pressure difference between the inlet and outlet ports (ie, pressure loss) is generated. When the differential pressure value reaches 0.35Mpa, the power is automatically turned on to display the signal.
Tình trạng sản phẩm:
The main technical parameters of the transmitter Technical Data
| Model Model | Working pressure Working pressure (MPa) | Value sender Switch setting (MPa) | Working temperature Temp.Range (°C) | Transmitter Power Power (V/A) |
| CM-I | 32 | 0.1+0.05 0.2+0.05 0.35+0.05 0.45+0.05 0.6+0.05 0.8+0.05 1+0.05 | -20~+80 | - |
| CS-III | ≤220/0.25 | |||
| CS-IV | ||||
| CS-V | ||||
| CM | ||||
| CMS | ||||
| CMS-I | ||||
| CY-I | 1.6 | |||
| CY-II | ||||
| YM-I | - | |||
| CYB-I | 0.35+0.05 | DC24/2 | ||
| ZS-I | -0.9 | -0.01~0.018 | ≤220V | |
| ZKF-II | -0.018 | DC24/2 |
THÔNG TIN THANH TOÁN
| |||||||||
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TÂN THÀNH CAM KẾT
- Sản phẩm, hàng hóa chính hãng.
- Giá cả cạnh tranh.
- Dịch vụ chăm sóc khách hàng tận tâm.
Thông Tin Công Ty
Chính sách và quy định
Đã thông báo
Hỗ trợ khách hàng
THÔNG TIN LIÊN HỆ:
-------------------------------
CÔNG TY TNHH THIẾT BỊ CÔNG NGHIỆP TTH
Trụ sở: số 124 ngõ 79 Yên Hoà-Cầu giấy-HN
Kinh doanh 1 : 0816.861.515
Kinh doanh 2 : 0836.861.515
Kinh doanh 3 : 0926.511.515
Kinh doanh 4 : 0916.861.515
Kinh doanh 5 : 0888.868.515
Kinh doanh 6 : 0917.971.515
Website: http://tanthanh-automation.com
Website: http://thietbitudongtanthanh.com
Website: http://diencongnghieptanthanh.com
Email: tthkinhdoanh@gmail.com
Email: tthkinhdoanh01@gmail.com
